请问各位给honey pelikan m400上啥颜色的墨水

spinon · 发表于 2005-9-20 14:57

谢谢乖兄，如何旋下笔尖？thanks again.

韦伯猫 · 发表于 2005-9-20 15:01

<DIV class=quote>以下是引用spinon在2005-9-20 14:57:08的发言： 谢谢乖兄，如何旋下笔尖？thanks again.</DIV>
 [em06][em06][em06][em06]

韦伯猫 · 发表于 2005-9-20 15:03

<DIV align=justify>
<

align=center><BIG>Instructions for changing Pelikan nibs</BIG>
<

align=justify>These nibs screw in using the conventional right-hand thread. Using your fingers only (don't use any type of tool), grip the nib close to the barrel, away from the point, and gently but firmly unscrew. Do not grip the nib by the edges, since doing so could mis-align the tines. If the pen is not new, dried ink could conceivably be "gluing" the current nib into the section and it may seem like it won't unscrew.
<

align=justify>In that case, soak the nib end of the pen, up to about 3/4" over the edge of the section, in household ammonia for ten minutes or so, and flush in and out during the soaking, to clean out the filling system itself. This should dissolve any dried ink. Dry off the nib/feed/section and try to unscrew the nib again. You may want to use a soft cloth or tissue so that your fingers don't get soiled. Some paper towels are coarse enough to scratch the gold finish on fountain pens and nibs, therefore we recommend soft cloths or soft tissues.
<

align=justify>When screwing in a nib, gently but firmly tighten into the section, and realize that it will require about the same amount of force to remove the nib as was required to tighten it. Do not over-tighten. 
<

align=justify> 
<

align=justify>REF: www.nibs.com</DIV>

spinon · 发表于 2005-9-20 15:07

thanks,cat elder brother.

jack120 · 发表于 2005-9-20 15:11

<

>household ammonia 
<

>家用氨水？什么玩艺，估计又要上化学用品商店了，呵呵

万宝鹈鹕鸟 · 发表于 2005-9-20 15:27

左手握牢笔杆，右手拿软布或餐巾纸握住笔尖的腰部，以免笔尖损伤，顺时针旋转即可卸下笔尖。

万宝鹈鹕鸟 · 发表于 2005-9-20 15:30

<

>老猫抢先一步，发重了。[em01]

[此贴子已经被作者于2005-9-20 15:33:15编辑过]

spinon · 发表于 2005-9-20 15:38

谢谢大家！

小乖乖 · 发表于 2005-9-21 08:00

<

0cm 0cm 0pt">根据小弟的经验，旋下时最好如万兄所言垫块软布以为缓冲。纯粹以手指拿捏，有时笔尖较紧或要将其旋紧时，力道拿捏得不好会导致笔尖移位或变形。而且假使垫块软布也会较好施力。不过M600以下的笔尖我会捏住笔尖面，因为其造型较圆，比较容易产生跑位的现象。

spinon · 发表于 2005-9-21 08:23

乖兄，谢谢，请问笔尖旋下后是否可以对笔进行清洗，如何进行？谢谢

		自动登录	找回密码
密码			论坛注册（注册原因请填：钢笔）